If your Chevy Silverado’s radio has stopped working, there’s a good chance you can reset it yourself by following these simple steps.
First, turn the truck off and unplug the radio.
Next, remove the two screws on the back of the radio and pull it out.
Now, locate the five small buttons on the bottom of the radio and press and hold the Reset button while plugging the radio back in.
Hold the button for about 15 seconds, or until the radio resets.
You can now replace the radio and screw it back in.
If your Chevy Silverado’s radio still isn’t working after resetting it, there’s a good chance you need to take it to a mechanic to have it repaired.
Contents
- 1 How do I reset my Silverado radio?
- 2 How do I reset my Chevy MyLink 2015 Silverado?
- 3 How do you reset the radio on a 2015 GMC Sierra?
- 4 How do you reset the radio in a 2016 Chevy Silverado?
- 5 How do I reset my 2015 GMC IntelliLink?
- 6 How do I reset my infotainment system?
- 7 How do I update my Chevy MyLink 2015 Silverado?
How do I reset my Silverado radio?
If your Chevy Silverado’s radio isn’t working right, you may need to reset it. This is a simple process, but it’s important to follow the steps in the right order.
First, make sure your truck is turned off. Then, use a coin or a flathead screwdriver to pry open the ashtray. Reach behind the radio and unplug the power cord.
Now, you’ll need to remove the four screws that hold the radio in place. Gently pull the radio out and disconnect the antenna cable.
Finally, plug the power cord back in and reattach the antenna cable. Replace the screws and close the ashtray. Turn on your truck and the radio should be working properly.
How do I reset my Chevy MyLink 2015 Silverado?
How do I reset my Chevy MyLink 2015 Silverado?
There are a few ways to reset your Chevy MyLink 2015 Silverado. One way is to use the Settings menu. Another way is to use the buttons on the radio.
To reset your Chevy MyLink 2015 Silverado using the Settings menu, follow these steps:
1. Press the Settings button on the radio.
2. Scroll down and select System.
3. Scroll down and select Reset System.
4. Select Yes to confirm.
The radio will reset and all settings will be restored to their defaults.
To reset your Chevy MyLink 2015 Silverado using the buttons on the radio, follow these steps:
1. Press and hold the Previous and Next buttons on the radio.
2. The radio will reset and all settings will be restored to their defaults.
How do you reset the radio on a 2015 GMC Sierra?
If you are experiencing problems with your radio on a 2015 GMC Sierra, you may need to reset it. This can be done by following a few simple steps.
First, make sure the vehicle is turned off. Next, locate the reset button on the back of the radio. It is a small, circular button located near the bottom. Push and hold the button for about 10 seconds until the radio resets.
If the reset button does not work, you may need to disconnect the battery. To do this, remove the negative terminal from the battery using a socket wrench. Once the terminal is off, wait a few minutes before reconnecting it. Then, push and hold the reset button for 10 seconds.
If you are still having problems with your radio, you may need to take it to a dealership for service.
How do you reset the radio in a 2016 Chevy Silverado?
If you’re having trouble with your radio in your 2016 Chevy Silverado, you may need to reset it. This process is easy to do and can be accomplished in just a few minutes.
To reset the radio, first make sure that it is turned off. Next, locate the reset button on the back of the unit. It’s a small, circular button located in the bottom-right corner.
Then, use a pen or another object to press and hold the button down for about five seconds. After that, release the button and turn the radio on. It should now be working properly.
If the reset process doesn’t fix the problem, you may need to take your truck to a Chevy dealer for further assistance.
How do I reset my 2015 GMC IntelliLink?
If you’re having trouble with your 2015 GMC IntelliLink, there may be a way to reset it. Here’s how to do it:
1. Turn off the car.
2. Remove the key from the ignition.
3. Open the driver’s side door.
4. Locate the reset button on the lower left side of the dashboard.
5. Push the button with a pen or paper clip.
6. Hold the button down for 10 seconds.
7. Release the button and close the driver’s side door.
8. Turn on the car.
Your IntelliLink should now be reset.
How do I reset my infotainment system?
Resetting an infotainment system can help alleviate any problems you may be experiencing with it. There are a few different ways to reset an infotainment system, and each method is a little bit different depending on the make and model of your vehicle.
One way to reset an infotainment system is to use the buttons on the system itself. If your infotainment system has a power button, a reset button, and a menu button, you can try resetting it using these buttons. First, turn the system off by pressing and holding the power button. Next, press and hold the reset button until the system turns on. Finally, release the reset button and press the menu button to see if the problem has been resolved.
If your infotainment system doesn’t have a power button, reset button, or menu button, you can try resetting it using the car’s key fob. This method is a little bit more complicated, but it can be useful if the buttons on the infotainment system aren’t working. To reset the system using the key fob, first turn the key to the “on” position and wait for the “ready” light to come on. Next, press and hold the power button on the key fob until the light starts flashing. Finally, press the “lock” button on the key fob three times. This will reset the infotainment system.
If you’re still having problems with your infotainment system after resetting it, you may need to take it to a mechanic. There could be a problem with the system itself that needs to be fixed.
How do I update my Chevy MyLink 2015 Silverado?
If you have a Chevy MyLink 2015 Silverado, you may be wondering how to update the system. Updating your Chevy MyLink 2015 Silverado is actually a very simple process. All you need is a USB drive and a computer.
First, you will need to download the update file from Chevy’s website. Once you have the file, you will need to copy it to your USB drive. Once the file is on your USB drive, you can plug it into your computer.
Next, you will need to open the file and run the update. Once the update is finished, you will need to unplug your USB drive and plug it back into your Chevy MyLink 2015 Silverado. The update will then be installed.
That’s all there is to it! Updating your Chevy MyLink 2015 Silverado is a very simple process and should only take a few minutes.